14 AWG Test Pin of UL 498:2017 Figure 136.2
Terminal Abuse Test
The same flush and self-contained receptacle having a 5-15R,5-20R，6-15R,or 6-20R configuration used for the conductor insertion and retention test and the conductor push-in test are to be tested as described in this section. The test conductors used in the previous tests are to be removed from the receptacles using the wire release mechanism.
Exception: For receptacles without a wire release mechanism, previously untested receptacles are to be used.
As a result of the test described in 136.3, there shall not be any breakage or distortion of the insulating body of the receptacle that:
a) Would expose live parts to contact by a 1/32 inch (0.79 mm) diameter rod, or
b) Results in reduction of electrical spacings to values less than those required for the receptacle.
Each receptacle is to be mounted in the test fixture shown in Figure 136.1 with its face in a vertical plane. The test pin shown in Figure 136.2 is then to be fully inserted into the “Push-In” terminal opening. An 8-ounce (0.23-kg) weight is to be gradually suspended from the test pin 6 inches(152 mm) from the plane of the terminal opening. The weight is to be applied for one minute, following which the weight is to be removed. The application of the weight is to be repeated with the receptacle rotated 90,180 and 270degrees for a total of four applications per receptacle.
14 AWG Test Pin of UL 498:2017 Figure 136.2
Lisun Instruments Limited was found by LISUN GROUP in 2003. LISUN quality system has been strictly certified by ISO9001:2015. As a CIE Membership, LISUN products are designed based on CIE, IEC and other international or national standards. All products passed CE certificate and authenticated by the third party lab.
Our main products are Goniophotometer, Integrating Sphere, Spectroradiometer, Surge Generator, ESD Simulator Guns, EMI Receiver, EMC Test Equipment, Electrical Safety Tester, Environmental Chamber, Temperature Chamber, Climate Chamber, Thermal Chamber, Salt Spray Test, Dust Test Chamber, Waterproof Test, RoHS Test (EDXRF), Glow Wire Test and Needle Flame Test.
Please feel free to contact us if you need any support.
Tech Dep: Service@Lisungroup.com, Cell/WhatsApp:+8615317907381
Sales Dep: Sales@Lisungroup.com, Cell/WhatsApp:+8618117273997
https://www.lisungroup.com/news/technology-news/14-awg-test-pin-of-ul-4982017-figure-136-2.html

Comments

Post a Comment

Popular posts from this blog

What are the differences of FMVSS 302, UL94 and IEC60695 for flammability test?

Image
The flammability of different materials, such as plastics and other materials used in items such as automobile interiors, electronic devices, and electrical appliances, is evaluated using a number of different standards. Some of these standards are FMVSS 302, UL 94, and IEC 60695. Nevertheless, there are a number of important distinctions between these standards: FMVSS 302 is a specialized standard that was designed for the automotive industry to analyze the flammability of materials used in car interiors. Its purpose is to measure the combustibility of these materials. The UL 94 standard is a more comprehensive regulation that assesses the combustibility of a variety of materials, including plastics, and has applications in a number of different sectors. IEC 60695 is a global standard that is used in the process of assessing the potential for electronic and electrical equipment to catch fire. Testing Procedures The flammability of materials is determined using a variety of testing ...
Read more
Image
125 Grounding Contact Test 125.1 Grounding receptacles having a 5-15R,5-20R，6-13R，6-20R，7-15R，14-15Ror 15-15R configuration are to be subjected to the tests in this section. 125.2 Previously untested devices are to be used. Each device is to be mounted in a flush device box, or as otherwise intended, with its face in a vertical plane. A nonmetallic faceplate is to be installed if intended. A solid 14 AWG (2.1 mm2) copper conductor is to be connected to the receptacle grounding terminal. GNGPL SB1610_AL 125.3 With the receptacle oriented to create the maximum contact displacement (possible distortion of contact affecting its contact ability), the test pin A. Figure 125.1 is to be fully inserted in the grounding contact. A 5 lb (2.27 kg) weight is to be gradually suspended form the test pin 6 inches (152 mm) from the face of the receptacle. The weight is to be applied for 1 minute, following which, the weight is to be removed. The application of the weight is to be repeated with the rece...
Read more
Image
Accessible parts of equipment with standard IEC 62368 General An accessible part of an equipment is a part that can be touched by a body part. For the purposes of dctermining an accessible part, a body part is represented by one or more of the specified test probes. Accessible parts of an equipment can include parts behind a door, panel, removable cover, etc. that can be opened without the use of a tool. Accessible parts do not include those that become accessible when floor standing equipment having a mass exceeding 40 kg is tilted. For equipment intended for building-in or rack-mounting, or for subassemblies and the like for incorporation in larger equipment,accessible parts do not include those that are not accessible when the equipment or subassembly is installed according to the method of mounting or installation specified in the installation instructions. A part is considered accessible if the instructions or markings intended to be followed require that a person phys...
Read more