How to use a temperature humidity test chamber for electronic components?

In order to put a temperature and humidity test chamber for electronic components to use, the following steps are required to be taken:

  • Prepare the testing equipment as follows: After giving the enclosure a good washing and making sure it is completely dry, check to make sure that the controls for the temperature and humidity have been correctly calibrated.
  • Arrangement of the electrical components inside the chamber should look like this: Verify that the components have been placed securely and that there is sufficient space between them to avoid any interference from occurring as a result of one another.
  • Initiate the test by stating that when the chamber has been switched on, the temperature and humidity levels should be adjusted according to your requirements. It is essential to provide the components permission to be exposed to these conditions for a certain amount of time.
  • Maintain a keen focus on the examination: Ensure that you remain vigilant over the measurements to guarantee that the levels of temperature and humidity will remain inside the boundaries that have been defined.
  • Put a stop to the experiment by switching off the chamber and removing all of the components one by one. Make some notes on the results, then inspect each component to see if there are any signs of wear and tear or degradation.
  • Repeat the test: If it is necessary, repeat the test using different levels of temperature and humidity or for a different amount of time in order to get a comprehensive understanding of how the components operate in a range of environments.

Note: Prior to using the test chamber, you should always examine the instructions that have been supplied by the manufacturer, and you should also make sure to take the proper precautions to safeguard both the staff and the components.

Comments

Post a Comment

Popular posts from this blog

What are the differences of FMVSS 302, UL94 and IEC60695 for flammability test?

Image
The flammability of different materials, such as plastics and other materials used in items such as automobile interiors, electronic devices, and electrical appliances, is evaluated using a number of different standards. Some of these standards are FMVSS 302, UL 94, and IEC 60695. Nevertheless, there are a number of important distinctions between these standards: FMVSS 302 is a specialized standard that was designed for the automotive industry to analyze the flammability of materials used in car interiors. Its purpose is to measure the combustibility of these materials. The UL 94 standard is a more comprehensive regulation that assesses the combustibility of a variety of materials, including plastics, and has applications in a number of different sectors. IEC 60695 is a global standard that is used in the process of assessing the potential for electronic and electrical equipment to catch fire. Testing Procedures The flammability of materials is determined using a variety of testing ...
Read more
Image
125 Grounding Contact Test 125.1 Grounding receptacles having a 5-15R,5-20R，6-13R，6-20R，7-15R，14-15Ror 15-15R configuration are to be subjected to the tests in this section. 125.2 Previously untested devices are to be used. Each device is to be mounted in a flush device box, or as otherwise intended, with its face in a vertical plane. A nonmetallic faceplate is to be installed if intended. A solid 14 AWG (2.1 mm2) copper conductor is to be connected to the receptacle grounding terminal. GNGPL SB1610_AL 125.3 With the receptacle oriented to create the maximum contact displacement (possible distortion of contact affecting its contact ability), the test pin A. Figure 125.1 is to be fully inserted in the grounding contact. A 5 lb (2.27 kg) weight is to be gradually suspended form the test pin 6 inches (152 mm) from the face of the receptacle. The weight is to be applied for 1 minute, following which, the weight is to be removed. The application of the weight is to be repeated with the rece...
Read more
Image
Accessible parts of equipment with standard IEC 62368 General An accessible part of an equipment is a part that can be touched by a body part. For the purposes of dctermining an accessible part, a body part is represented by one or more of the specified test probes. Accessible parts of an equipment can include parts behind a door, panel, removable cover, etc. that can be opened without the use of a tool. Accessible parts do not include those that become accessible when floor standing equipment having a mass exceeding 40 kg is tilted. For equipment intended for building-in or rack-mounting, or for subassemblies and the like for incorporation in larger equipment,accessible parts do not include those that are not accessible when the equipment or subassembly is installed according to the method of mounting or installation specified in the installation instructions. A part is considered accessible if the instructions or markings intended to be followed require that a person phys...
Read more