How do you do IPX3 water proof test for your end-products?

The IPX3 water resistance test is carried out in order to determine the degree of protection afforded to electronic and electrical equipment against the intrusion of water. As part of the testing method, the product will be sprayed with water from a variety of directions to determine whether or not it can tolerate being subjected to water spray without allowing water to enter the device's internal workings.

The following pieces of apparatus are needed in order to carry out the IPX3 waterproof test successfully:

  • Spray nozzle: This is what will be utilized to create a consistent spray of water on the item that is being evaluated.
  • Water supply: In order to successfully complete the test, you will need access to a source of clean water.
  • Testing chamber: The testing chamber is where the product being tested and the water spray are both contained throughout the testing process.
  • Equipment for recording data: This is what is used to record the circumstances of the test and the outcomes.

The IPX3 waterproof test consists of the following phases, which are outlined below:

  • The test chamber has to be prepared with the product that is going to be tested placed in the middle of the chamber. In order to prevent the product from shifting about within the testing chamber while it is being evaluated, it should be installed in there in a stable manner.
  • Establish a connection to the water supply. The water supply has to be established as a connection to the spray nozzle, and the spray nozzle needs to be positioned so that it can send water onto the product.
  • Launch the exam by saying: A minimum of five minutes should be spent directing the water spray at the product from a variety of various angles. At a minimum distance of three meters, the spray need to be directed onto the product while it is being held.
  • Document the findings: Using the appropriate data recording equipment, you should document both the test circumstances and the findings.
  • Examine the findings It is important to evaluate the results in order to establish whether or not the product satisfies the IPX3 waterproof standard. During the evaluation, the product in question must prevent any moisture from entering the device's inside.

In conclusion, the IPX3 waterproof test is carried out to determine the amount of protection afforded to electronic and electrical equipment against the intrusion of water. The product is subjected to a series of water sprays from a variety of directions as part of the test to determine whether or not it can resist the water sprays without letting water to enter the device's internal workings.

Comments

Post a Comment

Popular posts from this blog

What are the differences of FMVSS 302, UL94 and IEC60695 for flammability test?

Image
The flammability of different materials, such as plastics and other materials used in items such as automobile interiors, electronic devices, and electrical appliances, is evaluated using a number of different standards. Some of these standards are FMVSS 302, UL 94, and IEC 60695. Nevertheless, there are a number of important distinctions between these standards: FMVSS 302 is a specialized standard that was designed for the automotive industry to analyze the flammability of materials used in car interiors. Its purpose is to measure the combustibility of these materials. The UL 94 standard is a more comprehensive regulation that assesses the combustibility of a variety of materials, including plastics, and has applications in a number of different sectors. IEC 60695 is a global standard that is used in the process of assessing the potential for electronic and electrical equipment to catch fire. Testing Procedures The flammability of materials is determined using a variety of testing ...
Read more
Image
125 Grounding Contact Test 125.1 Grounding receptacles having a 5-15R,5-20R，6-13R，6-20R，7-15R，14-15Ror 15-15R configuration are to be subjected to the tests in this section. 125.2 Previously untested devices are to be used. Each device is to be mounted in a flush device box, or as otherwise intended, with its face in a vertical plane. A nonmetallic faceplate is to be installed if intended. A solid 14 AWG (2.1 mm2) copper conductor is to be connected to the receptacle grounding terminal. GNGPL SB1610_AL 125.3 With the receptacle oriented to create the maximum contact displacement (possible distortion of contact affecting its contact ability), the test pin A. Figure 125.1 is to be fully inserted in the grounding contact. A 5 lb (2.27 kg) weight is to be gradually suspended form the test pin 6 inches (152 mm) from the face of the receptacle. The weight is to be applied for 1 minute, following which, the weight is to be removed. The application of the weight is to be repeated with the rece...
Read more
Image
Accessible parts of equipment with standard IEC 62368 General An accessible part of an equipment is a part that can be touched by a body part. For the purposes of dctermining an accessible part, a body part is represented by one or more of the specified test probes. Accessible parts of an equipment can include parts behind a door, panel, removable cover, etc. that can be opened without the use of a tool. Accessible parts do not include those that become accessible when floor standing equipment having a mass exceeding 40 kg is tilted. For equipment intended for building-in or rack-mounting, or for subassemblies and the like for incorporation in larger equipment,accessible parts do not include those that are not accessible when the equipment or subassembly is installed according to the method of mounting or installation specified in the installation instructions. A part is considered accessible if the instructions or markings intended to be followed require that a person phys...
Read more